document number: 91240 www.vishay.com s09-0005-rev. a, 19-jan-09 1 power mosfet irfpc40, sihfpc40 vishay siliconix features ? dynamic dv/dt rating ? repetitive avalanche rated ? isolated central mounting hole ? fast switching ? ease of paralleling ? simple drive requirements ? lead (pb)-free available description third generation power mosfet s from vishay provide the designer with the best combi nation of fast switching, ruggedized device design, low on-resistance and cost-effectiveness. the to-247 package is preferred for commercial-industrial applications where higher power levels preclude the use of to-220 devices. the to-247 is similar but superior to the earlier to-218 package because of its isolated mounting hole. it also provides gr eater creepage distance between pins to meet the requirements of most safety specifications. notes a. repetitive rating; pulse width limited by maximum junction temperature (see fig. 11). b. v dd = 50 v, starting t j = 25 c, l = 16 mh, r g = 25 , i as = 6.8 a (see fig. 12). c. i sd 6.8 a, di/dt 80 a/s, v dd v ds , t j 150 c. d. 1.6 mm from case product summary v ds (v) 600 r ds(on) ( )v gs = 10 v 1.2 q g (max.) (nc) 60 q gs (nc) 8.3 q gd (nc) 30 configuration single n -channel mosfet g d s to-247 g d s a v aila b le rohs* compliant ordering information package to-247 lead (pb)-free irfpc40pbf sihfpc40-e3 snpb irfpc40 sihfpc40 absolute maximum ratings t c = 25 c, unless otherwise noted parameter symbol limit unit drain-source voltage v ds 600 v gate-source voltage v gs 20 continuous drain current v gs at 10 v t c = 25 c i d 6.8 a t c = 100 c 4.3 pulsed drain current a i dm 27 linear derating factor 1.2 w/c single pulse avalanche energy b e as 410 mj maximum power dissipation t c = 25 c p d 150 w peak diode recovery dv/dt c dv/dt 3.0 v/ns operating junction and storage temperature range t j , t stg - 55 to + 150 c soldering recommendations (p eak temperature) for 10 s 300 d mounting torque 6-32 or m3 screw 10 lbf in 1.1 n m * pb containing terminations are not rohs compliant, exemptions may apply
www.vishay.com document number: 91240 2 s09-0005-rev. a, 19-jan-09 irfpc40, sihfpc40 vishay siliconix notes a. repetitive rating; pulse width limited by maximum junction temper ature (see fig. 11). b. pulse width 300 s; duty cycle 2 %. thermal resistance ratings parameter symbol typ. max. unit maximum junction-to-ambient r thja -40 c/w case-to-sink, flat, greased surface r thcs 0.24 - maximum junction-to-case (drain) r thjc -0.83 specifications t j = 25 c, unless otherwise noted parameter symbol test conditions min. typ. max. unit static drain-source breakdown voltage v ds v gs = 0 v, i d = 250 a 600 - - v v ds temperature coefficient v ds /t j reference to 25 c, i d = 1 ma - 0.70 - v/c gate-source threshold voltage v gs(th) v ds = v gs , i d = 250 a 2.0 - 4.0 v gate-source leakage i gss v gs = 20 v - - 100 na zero gate voltage drain current i dss v ds = 600 v, v gs = 0 v - - 100 a v ds = 480 v, v gs = 0 v, t j = 125 c - - 500 drain-source on-state resistance r ds(on) v gs = 10 v i d = 4.1 a b --1.2 forward transconductance g fs v ds = 100 v, i d = 4.1 a b 4.9 - - s dynamic input capacitance c iss v gs = 0 v, v ds = 25 v, f = 1.0 mhz, see fig. 5 - 1300 - pf output capacitance c oss - 160 - reverse transfer capacitance c rss -30- total gate charge q g v gs = 10 v i d = 6.2 a, v ds = 360 v, see fig. 6 and 13 b --60 nc gate-source charge q gs --8.3 gate-drain charge q gd --30 turn-on delay time t d(on) v dd = 300 v, i d = 6.2 a , r g = 9.1 , r d = 47 , see fig. 10 b -13- ns rise time t r -18- turn-off delay time t d(off) -55- fall time t f -20- internal drain inductance l d between lead, 6 mm (0.25") from package and center of die contact -5.0- nh internal source inductance l s -13- drain-source body diode characteristics continuous source-drain diode current i s mosfet symbol showing the integral reverse p - n junction diode --6.8 a pulsed diode forward current a i sm --27 body diode voltage v sd t j = 25 c, i s = 6.8 a, v gs = 0 v b --1.5v body diode reverse recovery time t rr t j = 25 c, i f = 6.2 a, di/dt = 100 a/s b - 450 940 ns body diode reverse recovery charge q rr -3.87.9c forward turn-on time t on intrinsic turn-on time is neglig ible (turn-on is dominated by l s and l d ) d s g s d g
document number: 91240 www.vishay.com s09-0005-rev. a, 19-jan-09 3 irfpc40, sihfpc40 vishay siliconix typical characteristics 25 c, unless otherwise noted fig. 1 - typical output characteristics, t c = 25 c fig. 2 - typical output characteristics, t c = 150 c fig. 3 - typical transfer characteristics fig. 4 - normalized on-resistance vs. temperature
www.vishay.com document number: 91240 4 s09-0005-rev. a, 19-jan-09 irfpc40, sihfpc40 vishay siliconix fig. 5 - typical capacitance vs. drain-to-source voltage fig. 6 - typical gate charge vs. gate-to-source voltage fig. 7 - typical source-drain diode forward voltage fig. 8 - maximum safe operating area
document number: 91240 www.vishay.com s09-0005-rev. a, 19-jan-09 5 irfpc40, sihfpc40 vishay siliconix fig. 9 - maximum drain current vs. case temperature fig. 10a - switching time test circuit fig. 10b - switching time waveforms fig. 11 - maximum effective transient thermal impedance, junction-to-case p u lse w idth 1 s d u ty factor 0.1 % r d v gs r g d.u.t. 10 v + - v ds v dd v ds 90 % 10 % v gs t d(on) t r t d(off) t f
www.vishay.com document number: 91240 6 s09-0005-rev. a, 19-jan-09 irfpc40, sihfpc40 vishay siliconix fig. 12a - unclamped inductive test circuit fig. 12b - unclamped inductive waveforms fig. 12c - maximum avalanche energy vs. drain current fig. 13a - basic gate charge waveform fig. 13b - gate charge test circuit r g i as 0.01 t p d.u.t l v ds + - v dd 10 v v ary t p to o b tain re qu ired i as i as v ds v dd v ds t p q gs q gd q g v g charge 10 v d.u.t. 3 ma v gs v ds i g i d 0.3 f 0.2 f 50 k 12 v c u rrent reg u lator c u rrent sampling resistors same type as d.u.t. + -
document number: 91240 www.vishay.com s09-0005-rev. a, 19-jan-09 7 irfpc40, sihfpc40 vishay siliconix fig.14 - for n-channel vishay siliconix maintains worldwide manufacturing capability. pr oducts may be manufactured at one of several qualified locatio ns. reliability data for silicon technology and package reliability represent a composite of all qualified locations. for related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?91240 . p. w . period di/dt diode reco v ery d v /dt ripple 5 % body diode for w ard drop re-applied v oltage re v erse reco v ery c u rrent body diode for w ard c u rrent v gs = 10 v * v dd i sd dri v er gate dri v e d.u.t. i sd w a v eform d.u.t. v ds w a v eform ind u ctor c u rrent d = p. w . period + - + + + - - - * v gs = 5 v for logic le v el de v ices peak diode recovery dv/dt test circuit v dd ? d v /dt controlled b y r g ? dri v er same type as d.u.t. ? i sd controlled b y d u ty factor "d" ? d.u.t. - de v ice u nder test d.u.t. circ u it layo u t considerations ? lo w stray ind u ctance ? gro u nd plane ? lo w leakage ind u ctance c u rrent transformer r g
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
